No Hot Water? What to Check Before You Call a Plumber
No Hot Water? What to Check Before You Call a Plumber

If the hot tap runs cold everywhere in the house, the cause is almost always the water heater itself: a tank that has lost power or its flame, a failed part, or a tank that has reached the end of its life. A few safe checks take about ten minutes and sometimes fix it. Some signs mean you stop and call a licensed professional right away. This guide covers both, from our work on tanks across Port Coquitlam, Coquitlam and Port Moody.
TL;DR
- If every hot tap is cold, start at the water heater: check the power (electric) or the pilot and gas supply (gas), then the thermostat setting.
- If only one tap or shower is lukewarm, the heater is probably fine. Look at that fixture or its mixing valve instead.
- Smell gas, see water pooling around the tank, or find scorch marks or a tripping breaker? Stop troubleshooting and treat it as an emergency.
- A tank that is 10 to 15 years old, rusty, or leaking at the base is usually a replacement job, not a repair.
- We are available 24/7. Jon, the owner, comes out himself, quotes on site, and removes the old tank at no charge.
Table of Contents
- First, work out how big the problem is
- Checks for an electric water heater
- Checks for a gas water heater
- If you have a tankless water heater
- Hot water is cold at one tap only
- Lukewarm water, or hot water that runs out too fast
- When no hot water is an emergency
- Repair or replace?
- What we do when you call
- Perspective: why we tell people not to keep fixing an old tank
- Keep it from happening again
- FAQ
- Sources
First, work out how big the problem is
Before you open any panel, spend two minutes on these questions. They tell you where to look.
- Is it every hot tap, or just one? Run hot water at the kitchen sink, a bathroom sink and the shower. If only one is cold, the problem is local to that fixture.
- Is it totally cold, or lukewarm? A tank that has failed completely points to power, flame or a control. Lukewarm water that runs out fast points to a worn element, a sediment-filled tank or a failing tank.
- Did it change suddenly, or fade over weeks? A sudden loss suggests a tripped breaker, a pilot that went out or a failed part. A slow fade suggests wear.
- What kind of heater do you have? Look at the label on the tank. Gas tanks have a vent pipe on top and a gas line at the bottom. Electric tanks have a wire feed into the top and no flue. Tankless units are mounted on the wall and have a gas or electric supply.
- Is there any sign of a leak? Check the floor around the tank and the pipes above it.
If the answer to that last one is yes, skip down to the section on when to stop.
Checks for an electric water heater
Electric tanks are simple, and most no-hot-water calls on them come down to power or a heating element.
- Check the breaker. Open your electrical panel and look for a tripped breaker labelled for the water heater. Switch it fully off, then back on. If it trips again straight away, leave it off. A breaker that keeps tripping is telling you something is wrong with the heater or its wiring.
- Check the thermostat setting. Someone may have turned it down, or it may have been knocked. Do not open the access panels on the heater unless you are confident working near live electrical components. If you are not, this is a good point to stop.
- Listen and feel. A working element makes a faint hum or ticking as the tank heats. Silence for an hour with power confirmed at the breaker suggests a failed element, thermostat or high-limit switch.
Most electric heaters have a high-limit reset button behind the upper access panel. It trips when the water overheats. Pressing it is a task for someone comfortable around 240-volt wiring, and if it trips again after a reset, something is failing and the heater needs a proper diagnosis.
Electrical work beyond the water heater, such as a damaged circuit or panel problem, is something we can arrange through our subcontracted electrical services.
Checks for a gas water heater
Gas tanks lose hot water mostly because the burner is not firing. The most common reason is a pilot light that has gone out.
- Confirm the gas is on. Check that the shutoff valve at the heater is open (handle in line with the pipe). Check that another gas appliance, such as your stove, works. If none does, the problem is upstream of your heater.
- Check the thermostat dial on the gas control valve. Make sure it is set to a warm setting, not to pilot or off.
- Look at the pilot. On models with a pilot light, a small window near the bottom lets you see the flame. If it is out, the manufacturer’s relighting instructions are printed on the tank label. Follow them exactly.
- Notice what happens after relighting. If the pilot will not stay lit, or goes out again, the usual culprit is a worn thermocouple. That is a small safety sensor, and a failing one is a sign to book a gas fitter rather than keep relighting.
Newer tanks often use electronic ignition and have no standing pilot. Those usually show a blinking diagnostic light on the control. The label on the tank explains the code. A code that returns after a reset needs a service visit.
Do not attempt to repair gas valves, burners or gas connections yourself. Manufacturers say plainly that improper adjustments, alterations, service or maintenance can lead to property damage, injury or death and can void your warranty. In BC, gas work is done by a licensed gas fitter, and that is what we are.
If you have a tankless water heater
Tankless units fail differently. You will usually see an error code on the display, and the unit may switch itself off for safety.
- Check that the gas supply and the power to the unit are on. Tankless units need both.
- Check the display for a code and look it up in the manual.
- Check that the water flow is strong enough. Low flow, or a clogged inlet filter, can stop a unit from firing.
- If you see a code relating to venting, ignition or overheating, call a professional. Venting faults in particular can create a carbon monoxide risk.
Tankless installations also depend on the gas line being sized for the load. Manufacturer installation manuals state that installation must follow local codes or, in Canada, CSA B149.1. That is the code we work to.
Hot water is cold at one tap only
If the rest of the house is fine, the heater is not the problem. Look at:
- A single-handle faucet cartridge that has worn or clogged.
- A shower mixing valve that has failed or is stuck.
- A crossover. If hot and cold have been connected wrongly or a valve is leaking between them, hot water can cool unexpectedly.
- Low pressure at that fixture. A clogged aerator or a partly closed stop valve can reduce flow. Our guide on low water pressure at the kitchen sink walks through those checks.
Lukewarm water, or hot water that runs out too fast
This is the pattern we see on ageing tanks. Typical causes:
- Sediment built up at the bottom of the tank, which insulates the water from the burner or lower element.
- A failed upper or lower element (electric), which halves the tank’s usable hot water.
- A broken dip tube, which sends cold water straight to the top of the tank.
- A thermostat set too low, or one that is no longer reading correctly.
- A tank that is simply too small for current household use after a family has grown or fixtures have been added.
Sediment removal and element replacement can extend the life of a younger tank. They are poor value on an old one.
When no hot water is an emergency
No hot water on its own is an inconvenience. It becomes an emergency when it comes with any of these:
- A gas smell. Natural gas is given an odour so you can detect it. If you smell it, do not turn lights or switches on or off, do not use your phone inside, and do not try to relight anything. Leave the house, then call from outside. FortisBC emergency and gas-leak guidance should be your first call for a suspected leak in the street or the meter; for the appliance itself, call us once everyone is out and safe.
- Active leaking or flooding around the tank. Active leaking, a gas smell, electrical risk or flooding are the points at which a loss of hot water becomes a plumbing emergency. Shut off the water supply to the tank at the cold inlet valve, and if it is safe to reach, shut off the power or gas to it.
- Soot, scorching or a burning smell around the heater or its vent.
- Headaches, nausea or dizziness when the heater runs, or a carbon monoxide alarm sounding. Get everyone outside into fresh air and call 911. Health Canada notes that carbon monoxide has no smell, colour or taste and recommends certified CO alarms on every level of the home, especially near sleeping areas.
- A tank that has been under floodwater. A water heater or its controls that have been submerged should not be operated and need to be inspected, and replaced where needed, by a qualified technician.
If water is already pooling and you are not sure where it is coming from, our emergency plumbing service runs around the clock.
Repair or replace?
This is the question most people have by the time they call. The honest answer depends on age, condition and what failed.
Water heaters generally last about 10 to 15 years. CAA-Québec lists the signs that point toward replacement: water that is less hot or runs out faster, reddish water, rust at the bottom of the tank, or moisture and droplets around it. The same logic applies to gas tanks.
| Situation | Usually |
|---|---|
| Tank under about 8 years old, one failed part (element, thermocouple, thermostat, gas valve) | Repair |
| Tank 10 to 15 years old with a failed part | Repair only if the part is cheap and the tank is otherwise clean; often replace |
| Water leaking from the tank body or the seam | Replace. A leaking tank cannot be patched |
| Rusty water from the hot tap only | Replace if the tank interior is corroding |
| Rust or moisture at the bottom of the tank | Replace |
| Dripping T&P valve | Check water pressure first; this may be a pressure issue rather than a failed tank |
That last row matters. A dripping temperature and pressure relief valve is often blamed on the heater when the cause is the house. Manufacturer guidance explains that water pressure above 80 psi can make T&P valves drip, which calls for a pressure reducing valve. Replacing the tank without addressing the pressure just means the new valve drips too.
A tank that is leaking from the body cannot be repaired. If the tank is the problem, the useful question is how quickly you can have a new one in.

What we do when you call
We are an owner-led company. When you call, you reach us, and Jon is the technician who comes to the house. Here is how a typical no-hot-water call goes:
- You call, any hour. We ask what you are seeing and tell you what to do in the meantime, including what to shut off if there is a leak.
- Jon diagnoses on site. We check power, fuel, controls, venting, the tank condition and the water pressure.
- You get a straight answer. Fix it or replace it, and why. If a repair makes sense, we say so. If the tank is at the end of its life, we say that too.
- You get a clear price before work starts. Our call-out fee is $60, and it is waived if the work goes ahead.
- We do the work to code as licensed gas fitting and plumbing, whether the job is a part swap or a full tank installation.
- We haul the old tank away with no disposal charge.
If the verdict is a new tank, or you are thinking about going tankless, see our water heater service and installation page. For a gas heater that needs a new gas line, vent or connection, our gas fitting team handles that in the same visit.
Perspective: why we tell people not to keep fixing an old tank
We get a lot of calls at the worst hour, with a family waiting for a shower or a cold basement floor. The temptation is to patch it and hope. Sometimes that is the right call. A thermocouple on a six-year-old tank is a cheap repair and we will do it gladly.
But a 14-year-old tank with a failed element and rust at the base is a different story. You pay for the repair, and then the tank fails again within a year, often when you are away or at night. A tank that fails by leaking can damage flooring and drywall far beyond the cost of replacing it.

So we look at the tank, not only the part that failed. We tell you the age, the condition and what we would do if it were our own house. If a repair is the better value, you get the repair. If it is time to replace, you get a clear price, a quick install and the old tank taken away at no extra cost. We never want to sell you something you do not need, because we would rather you call us again in ten years than regret calling us once.
The other thing we tell everyone: do not do gas work yourself, and do not ignore a gas smell. Those are the two situations where waiting costs more than a call.
— Jon
Keep it from happening again
A few habits stretch the life of a tank and give you warning before it fails.
- Look at the tank twice a year. Check for moisture, rust streaks or drips around the base and on the fittings.
- Know where your shutoffs are. The cold inlet valve on top of the tank and the gas valve or breaker. In a leak, this is what limits the damage.
- Book annual servicing for gas appliances. FortisBC says annual maintenance by a licensed gas contractor can help gas appliances operate at their best.
- Install CO alarms on each level, near bedrooms, and test them.
- Note the tank’s age. The date is on the data label. When it passes about 10 years, plan the replacement rather than waiting for the failure.
- Watch for drain trouble alongside it. If hot water problems arrive with slow drains or gurgling, a plumbing problem further along may be involved. Our guide on a slow bathtub drain covers the first checks.
If you manage a strata or rental building, a failed central tank affects every unit. Keeping a record of tank age and service dates makes the replacement decision much easier, and it is worth having a plumber on call who answers at night.
FAQ
Why is there no hot water in my house all of a sudden?
When every hot tap goes cold at once, the heater has usually lost power or its flame. On an electric tank, check the breaker. On a gas tank, check that the gas is on and the pilot is lit. If both look fine, a failed element, thermostat or thermocouple is likely and needs a professional.
Is there a reset button on a hot water heater?
Most electric tanks have a high-limit reset button behind the upper access panel, and some gas controls have a reset or ignition button. Pressing it is only safe if you are comfortable working near the wiring and the unit is isolated. If it trips again after one reset, do not keep pressing it. Something is failing.
Why is my shower not as hot as it used to be?
If only the shower is affected, the cause is often a worn mixing valve or cartridge. If every tap is less hot, or the hot water runs out sooner, sediment, a failed element or an ageing tank is more likely. A tank over 10 years old that does this is worth having assessed.
What should I do if I smell gas near my water heater?
Do not touch switches, do not use a flame and do not try to relight the pilot. Get everyone out of the house, then call from outside. Once the area is safe, a licensed gas fitter needs to find and fix the source before the heater is used again.
Can I wait until morning to call a plumber?
If there is no leak, no gas smell and no tripping breaker, you can usually wait. Shut off the power or gas to the heater if you want to be careful. If you see water pooling or smell gas, call right away. We answer 24/7.
Sources
- How to Fix a Water Heater Pilot Light, Family Handyman
- User’s Information Manual, tankless water heater
- High efficiency commercial gas water heater installation and operation manual
- What to Do in the First 60 Seconds of a Plumbing Emergency
- Poisonings and injuries related to carbon monoxide exposure, Health Canada
- Electric water heater: choosing the right capacity, CAA-Québec
- Maintenance and troubleshooting guide, water heater manufacturer
- Appliance maintenance and safety, FortisBC
